ACTFEL

Information about ACTFEL

Published on January 24, 2008

Author: Calogera

Source: authorstream.com

Content

Electroluminescent Lamps:  Electroluminescent Lamps The Luxprint Electroluminescent Inks for this activity were donated by DuPont. Outline:  Outline Motivation History Final Schematic Useful Physics Thin film Capacitors (AC) Luminescence from phosphors How to make one: Overview Lithography: patterning ITO Applying the phosphor Power up/ testing/ trouble shooting Definitions/ Glossary Motivation:  Motivation Electroluminescence is the direct conversion of electricity to light. Electroluminescence is cool light, unlike incandescent lamps where light is generated by heating a filament to high temperatures. The heat from the lamps barely increase by 1° C above ambient temperature. Solid state lighting. Unlike incandescent lighting there is no filament and therefore no critical failure. Light output decays with age. EL lamps are probably the most rugged lighting technology available. A promising future Thanks to recent advances in electronics and materials chemistry, EL lamps have re-emerged as an innovative and exciting lighting technique. Facts taken from An Introduction to Dupont's Screenprintable EL Material System History of Electroluminescence:  History of Electroluminescence 1936: EL was discovered by a G. Destriau. 1940's: Chrysler tested EL for Automotive Applications. 1950's: Sylvania developed and sold EL night lights. 1960's: The industry saw decline. 1970's: Acceptance of EL lamps in the aircraft industry. 1980's: EL hit the automotive market and held on to aviation. 1990's: EL continues in automotive, aviation, and is entering consumer markets. Taken from An Introduction to Dupont's Screenprintable EL Material System Types of Electroluminescent Devices:  Types of Electroluminescent Devices from ETRI ACTFEL Lamps: Schematic of Final Lamp:  ACTFEL Lamps: Schematic of Final Lamp The ITO and Silver layers act as two plates of a capacitor. The ITO is transparent, so the photons can pass through the layer. The AC current produces a changing electric field in the capacitor that excites the phosphor. The excited phosphors emit light. The dielectric evens out the E field, reflects light, and prevents the capacitor from shorting. ACTFEL Lamps: Cross-section of Final Lamp:  ACTFEL Lamps: Cross-section of Final Lamp ACTFEL Lamps: Basic Physics:  ACTFEL Lamps: Basic Physics Alternating Current Thin Film Electroluminescent Lamps are essentially just capacitors. The electric field found inside a parallel plate capacitor is used to excite phosphor molecules. The excited phosphor emits light. ACTFEL Lamps: Basic Physics, Continued:  ACTFEL Lamps: Basic Physics, Continued Small green circles are manganese atoms. Large blue circles are excited manganese atoms. The horizontal dashes represent mobile electrons in the phosphor particle. Electrons in the phosphor particles are driven by the electric field. These electrons slam into manganese atoms in the phosphor and excite them. The excited manganese atoms relax by emitting a visible photon. The motion of the electrons is proportional to the electric field. The electric field is proportional to the applied voltage and inversely proportional to the electrode separation. Thus the brightness will increase by raising the voltage or thinning the phosphor and the dielectric layers. Energy Band Diagram for ACTFEL:  Energy Band Diagram for ACTFEL Making an EL Lamp: Overview:  Making an EL Lamp: Overview Photolithography: patterning ITO Applying the phosphor, dielectric, and silver layers Power up/ testing/ trouble shooting Patterning the ITO by Photolithography :  Patterning the ITO by Photolithography One way to shape the EL lamp is by patterning the ITO electrode. Only the phosphor under the ITO electrode will be excited. Photolithography is used to transfer a pattern. The ITO coated glass is covered with a photo resist The resist is exposed under a mask of the desired pattern. The resist is developed. The exposed sections of the resist dissolve while the unexposed sections harden (positive type resist). See the photolithography slideshow for further details. Patterning ITO coated slides:  Patterning ITO coated slides After a pattern has been transferred, the ITO layer of the ACTFEL lamp can be etched. A solution of hydrochloric acid and nitric acid will oxidize and remove the conductive metal oxide. The etched pattern shown below was created by photolithography using the mask shown to the right. Other lithographic techniques (such as molecular beam epitaxy) can be used to etch the ITO Note: The pattern is reversed because the lamp will be viewed from the opposite side of the glass. Notes on Etching: What type of patterns don’t work?:  Notes on Etching: What type of patterns don’t work? The phosphor under the ITO electrode will only be excited if the ITO has current running through it. Notice that the ITO inside the capital "D" is not connected to the rest of the ITO. This section of ITO lacks current. What type of patterns work?:  What type of patterns work? The pattern to the right is the same as the pattern in the last slide, but the inside of the “D” has been connected to the rest of the ITO. Now this section of the ITO will have power. Applying Thin Films:  Applying Thin Films After the ITO is patterned the ACTFEL lamp can made. Each layer comes packaged separately as a thick paste (stir before using). The thickness of each layer is controlled by using scotch tape as a spacer. Apply scotch tape along 3-5mm on two parallel sides of the plate. Apply the pastes in sequence using a spatula. Thin them by scraping a microscope slide across the layer. Dry and cure each layer before application of the next Each layer is dried in an oven at 130°C for ~15 minutes. 1st phosphor (Luxprint 8152) 2nd dielectric (Luxprint 8153) 3rd conductive silver rear electrode (Luxprint 9145) Applying Thin Films:  Applying Thin Films The dielectric layer should cover all of the phosphor layer and be as thin as possible without risking a short in the capacitor. The silver layer must not touch the ITO. Parts of the ITO layer are removed in order to extend the silver layer to the edge of the glass. This makes it easier to connect the lamp to a power source. The black lines mark the etched ITO pattern, and are used to accurately place the scotch tape; they’re later removed with acetone. Phosphor Layer Dielectric Layer Silver Layer (Rear Electrode) Cross-section of TFEL display The thin films must be applied to the substrate within defined boundaries to avoid shorting the capacitor. Layer Constraints The phosphor layer should be as thin as possible Power Up:  Power Up After the thin films are dry, the lamp needs a power source. Copper tape is used to make good contacts without damaging the lamp. Small pieces of tape are attached to the ITO layer and the silver layer separately. The phosphor requires a changing electric field in order to fluoresce. A DC voltage will only produce a changing electric field in a capacitor as it charges. In order to produce continuous lighting an AC voltage is required. Normal 110V 60Hz AC power can be used to light your lamp. In the lab we use a high frequency power supply 60-2000 Hz and a few hundred volts, which gives a brighter light. Front and back of device Device with leads on, powered, and in darkness. Trouble Shooting: Non-uniformity of Lighting:  Trouble Shooting: Non-uniformity of Lighting Notice the dark regions along the bottom and upper left corner of the display. This non-uniformity is caused by an irregularity in the thickness of the thin films. The difference in thickness between the center of the display and the dark band at the bottom is about 16 microns. Areas where the film is thinner will be brighter because the electric field is larger here. Thicker areas will be dimmer. Definitions/ Glossary::  Definitions/ Glossary: ACTFEL – alternating current thin film electroluminescence; gives off light when influenced by electrical current. Electroluminescence – the direct conversion of electrical energy into light. Thin layer - a very thin deposition of a colloidal substance (phosphor, dielectric, silver) onto the ITO coated glass plate. ITO – Indium Tin Oxide (In203:Sn02) A thin layer of indium oxide that has been doped with tin; transparent, conductive coating on glass plate. Phosphor – powders made of materials such as zinc sulfide, doped with either copper or manganese to achieve the emission colors when exposed to an electric field. Dielectric layer – an insulating layer that serves to even out the electric field across the phosphor layer and prevents short circuits. The dielectric in this case is barium titanate. Electrodes – form the plates of the capacitor; one front electrode of transparent ITO and one back electrode of silver. Acknowledgements The Luxprint Electroluminescent Inks for this lab were donated by DuPont Microcircuit Materials. http://www.mcm.dupont.com Initial development of this lab activity was performed by James Dizikes and Lloyd Bumm with the support of a Nanotechnology Undergraduate Education program grant. NSF DMR-0304664

Related presentations


Other presentations created by Calogera

23 Bacteria III Gram Positive
13. 02. 2008
0 views

23 Bacteria III Gram Positive

PNC
09. 01. 2008
0 views

PNC

Lec12 ImageGeneration s06
14. 01. 2008
0 views

Lec12 ImageGeneration s06

educational foundation
16. 01. 2008
0 views

educational foundation

uncoveringfreemasonry
17. 01. 2008
0 views

uncoveringfreemasonry

sighthear
18. 01. 2008
0 views

sighthear

solar energy Barnard
21. 01. 2008
0 views

solar energy Barnard

278 airpollutants
22. 01. 2008
0 views

278 airpollutants

chocolate
22. 01. 2008
0 views

chocolate

Lec6 3rd
22. 01. 2008
0 views

Lec6 3rd

2007 pot KSNA
23. 01. 2008
0 views

2007 pot KSNA

8 Reforming American Society
24. 01. 2008
0 views

8 Reforming American Society

Randy Perry 2007 retreat
24. 01. 2008
0 views

Randy Perry 2007 retreat

Chaver
12. 01. 2008
0 views

Chaver

wp 16 e
05. 02. 2008
0 views

wp 16 e

ChildhoodAdolescence
04. 02. 2008
0 views

ChildhoodAdolescence

Rattle Those Pots Pans
11. 02. 2008
0 views

Rattle Those Pots Pans

book review
11. 02. 2008
0 views

book review

06 cdf grijalva update
11. 01. 2008
0 views

06 cdf grijalva update

IPE Systems of Political Economy
28. 01. 2008
0 views

IPE Systems of Political Economy

2 6NOVO
29. 01. 2008
0 views

2 6NOVO

NativeAmer4
13. 02. 2008
0 views

NativeAmer4

Obedience to authority
15. 02. 2008
0 views

Obedience to authority

TBLT
18. 02. 2008
0 views

TBLT

Versenyeredmenyek
06. 02. 2008
0 views

Versenyeredmenyek

V Stratosphere
20. 02. 2008
0 views

V Stratosphere

Research issues
21. 01. 2008
0 views

Research issues

depression
28. 02. 2008
0 views

depression

Hierarchy
03. 03. 2008
0 views

Hierarchy

Taller CR Caso Honduras
07. 03. 2008
0 views

Taller CR Caso Honduras

Religions
08. 03. 2008
0 views

Religions

Passport to Your County Wayne
14. 03. 2008
0 views

Passport to Your County Wayne

UIS Sloan C Workshop 9Sep04
16. 01. 2008
0 views

UIS Sloan C Workshop 9Sep04

aed power point
15. 03. 2008
0 views

aed power point

zoonoses arbo 2004
07. 04. 2008
0 views

zoonoses arbo 2004

grid a ltc gec 2007 05 07
21. 01. 2008
0 views

grid a ltc gec 2007 05 07

06 C 1 FS J Orientation
27. 03. 2008
0 views

06 C 1 FS J Orientation

Valkommen till Peab
08. 02. 2008
0 views

Valkommen till Peab

InvitedTalk2
10. 04. 2008
0 views

InvitedTalk2

20071211542380
16. 04. 2008
0 views

20071211542380

YellowBlack it
17. 04. 2008
0 views

YellowBlack it

CIC Keynote Reeves Nov06
15. 01. 2008
0 views

CIC Keynote Reeves Nov06

CLAS100508 Week 4
21. 04. 2008
0 views

CLAS100508 Week 4

ITC new LOT1
24. 04. 2008
0 views

ITC new LOT1

GTW
07. 05. 2008
0 views

GTW

Chinas Currency Manipulation
08. 05. 2008
0 views

Chinas Currency Manipulation

780 1
30. 04. 2008
0 views

780 1

MWRIndocOnLine
02. 05. 2008
0 views

MWRIndocOnLine

Hilder
02. 05. 2008
0 views

Hilder

Hildegardgarden
05. 02. 2008
0 views

Hildegardgarden

unit10 reading20
15. 01. 2008
0 views

unit10 reading20

Verrazano
20. 03. 2008
0 views

Verrazano

Ladybugs
17. 01. 2008
0 views

Ladybugs

Nimbus TOMS 3
20. 02. 2008
0 views

Nimbus TOMS 3

HiddenGraphs prj
05. 03. 2008
0 views

HiddenGraphs prj

WPA Heidi Poster 06 final
17. 01. 2008
0 views

WPA Heidi Poster 06 final

Sipho
11. 01. 2008
0 views

Sipho

physicsofsports new
23. 01. 2008
0 views

physicsofsports new

HFDH 14 Laurent Nicq ConvergeX
08. 04. 2008
0 views

HFDH 14 Laurent Nicq ConvergeX