phase transformation

Information about phase transformation

Published on January 9, 2008

Author: Raffaele

Source: authorstream.com

Content

Slide1:  Phase Transformation Chapter 9 Slide2:  Shiva-Parvati, Chola Bronze Ball State University Q: How was the statue made? A: Invest casting Liquid-to-solid transformation An example of phase transformation Slide3:  Czochralski crystal pulling technique for single crystal Si Slide4:  Quenching of steel components a solid->solid phase transformation Slide5:  Liquid solidification evaporation sublimation Solid gas melting condensation Solid state phase transformation Solid 2 1 Slide6:  Thermodynamic driving force for a phase transformation Decrease in Gibbs free energy Liquid-> solid gs - gl = g = -ve Slide7:  g gL gS gS < gL gL < gS Liquid is stable Tm T Gibbs free energy as a function of temperature, Problem 2.3 gL gS g Solid is stable Tfreesing Fig. 9.1 Slide8:  How does solidification begins? Usually at the walls of the container Why? To be discussed later. Heterogeneous nucleation. Slide9:  Spherical ball of solid of radius R in the middle of the liquid at a temperature below Tm Homogeneous nucleation gL = free energy of liquid per unit volume gS = free energy of solid per unit volume g = gS - gL Slide10:  Change in free energy of the system due to formation of the solid ball of radius r : +ve: barrier to nucleation r r* Slide11:  r r* Solid balls of radius r < r* cannot grow as it will lead to increase in the free energy of the system !!! Solid balls of radii r > r* will grow r* is known as the CRITICAL RADIUS OF HOMOGENEOUS NUCLEATION Slide12:  r r* Eqn. 9.5 Eqn. 9.4 Slide13:  T Eqn. 9.7 Slide14:  f r Eqn. 9.8 Eqn. 9.7 Fig. 9.3 r1* f1* f2* r2* T1 T2 < Slide15:  Critical particle Fig. 9.4 Formation of critical nucleus by statistical flucctuation Atoms surrounding the critical particle Diffuse jump of a surrounding atom to the critical particle makes it a nucleation Slide16:  The Nucleation Rate Nt=total number of clusters of atoms per unit volume N* = number of clusters of critical size per unit volume By Maxwell-Boltzmann statistics Slide17:  s*= no. of liquid phase atoms facing the critical sized particle Hd = activation energy for diffusive jump from liquid to the solid phase  = atomic vibration frequency The rate of successful addition of an atom to a critical sized paticle Eqn. 9.10 Eqn. 9.9 Slide18:  Rate of nucleation, I , (m3 s-1) With decreasing T 1. Driving force increases 2. Atomic mobility decreases = No. of nucleation events per m3 per sec = number of critical clusters per unit volume (N*) x rate of successful addition of an atom to the critical cluster (’) Eqn. 9.11 Slide19:  Growth Increase in the size of a product particle after it has nucleated Slide20:  Overall Transformation Kinetics U I dX/dt T I : Nucleation rate U : Growth rate Overall transformation rate (fraction transformed per second) X=fraction of product phase Slide21:  Fraction transformed as a function of time ts tf X t Slow due to very few nuclei Slow due to final impingement Slide22:  TTT Diagram for liquid-to-solid transformation T Stable liquid Under Cooled liquid crystal Crystallization begins L+ Crystallization ends log t Tm C- curves Slide23:  TTT Diagram for liquid-to-solid transformation Coarse grained crystals Fine grained crystals glass Slide24:  T log t ts metals ts SiO2 Hd ∝ log (viscosity) Metals: high hm, low viscosity SiO2: low hm, high viscosity Silica glass Metallic glass Eqn. 9.11 Eqn. 9.8 Slide25:  Cooling rate 106 ºC s-1 F r o m P r i n c i p l e s o f E l e c t r o n i c M a t e r i a l s a n d D e v i c e s , S e c o n d E d i t i o n , S . O . K a s a p ( © M c G r a w - H i l l , 2 0 0 2 ) h t t p : / / M a t e r i a l s . U s a s k . C a Melt Spinning for metallic glass ribbons Slide26:  L+ T log t Tm T Tm Tg Log (viscosity) 12 18 crystal Stable liquid Undercooled liquid glass 30 Fig. 9.17 Slide27:  Tm Specific volume Stable liquid Undercooled liquid Fast cool Slow cool Tgs Tgf crystal Fig. 9.18 T Slide28:  log t L+ T Stable liquid Undercooled liquid Tm devitrification time T Glass ceramics nucleation growth glass Glass ceramic Liquid glass crystal Very fine crystals Slide29:  Corning’s new digital hot plates with PyroceramTM tops. Corningware PyroceramTM heat resistant cookware ROBAX® was heated until red-hot. Then cold water was poured on the glass ceramic from above - with NO breakage. Slide30:  Czochralski crystal pulling technique for single crystal Si SSPL: Solid State Physics Laboratory, N. Delhi J. Czochralski, (1885-1953) Polish Metallurgist Slide31:  You may collect slide handouts for chapters 6, 7 and 8 from Scoops Xerox Shop no more grades, no more pencils, no more sharing/using stencils, no more reading, no more books, no more teachers dirty looks, so when we hear that final bell, we drop our books and run like hell !! Slide32:  A Steel Hardness Rockwell C 15 0.8 Wt% C Micro-structure Coarse pearlite fine pearlite bainite Tempered martensite martensite 0.8 0.8 0.8 0.8 30 45 55 65 Heat treatment Annealing normalizing austempering tempering quenching B C D E TABLE 9.2 Slide33:  HEAT TREATMENT Heating a material to a high temperature, holding it at that temperature for certain length of time followed by cooling at a specified rate is called heat treatment Slide34:  A N AT T Q heating holding time T Annealing Furnace cooling RC 15 Normalizing Air cooling RC 30 Quenching Water cooling RC 65 Tempering Heating after quench RC 55 Austempering Quench to an inter- RC 45 mediate temp and hold Slide35:  Ammount of Fe3C in Pearlite Red Tie Line below eutectoid temp Slide36:  Phase diagrams do not have any information about time or rates of transformations. We need TTT diagram for austenite-> pearlite transformation Slide37:  Stable austenite unstable austenite TTT diagram for eutectoid steel start finish Slide38:  Annealing: coarse pearlite Normalizing: fine pearlite TTT diagram for eutectoid steel Slide39:  Callister Slide40:  Stable austenite unstable austenite start finish TTT diagram for eutectoid steel A+M M Ms Mf Ms : Martensite start temperature Mf : Martensite finish temperature ’: martensite (M) QUENCHING Hardness RC 65 Extremely rapid, no C-curves Slide41:  BCT Amount of martensite formed does not depend upon time, only on temperature. Atoms move only a fraction of atomic distance during the transformation: 1. Diffusionless (no long-range diffusion) 2. Shear (one-to-one correspondence between  and ’ atoms) 3. No composition change Martensitic transformation Slide42:  Problem 3.1 BCT unit cell of  (austenite) BCT unit cell of ’ (martensite) 0% C (BCC) 1.2 % C Martensitic transformation (contd.) Fig. 9.12 Slide43:  Hardness of martensite as a function of C content Wt % Carbon → 20 40 60 0.2 0.4 0.6 Hardness, RC Hardness of martensite depends mainly on C content and not on other alloying additions Fig. 9.13 Martensitic transformation (contd.) Slide44:  A N AT T Q heating T Slide45:  Heating of quenched steel below the eutectoid temperature, holding for a specified time followed by ar cooling. TEMPERING T<TE ? Slide46:  Tempering (contd.) +Fe3C PEARLITE A distribution of fine particles of Fe3C in  matrix known as TEMPERED MARTENSITE. Hardness more than fine pearlite, ductility more than martensite. Hardness and ductility controlled by tempering temperature and time. Higher T or t -> higher ductility, lower strength Slide47:  Tempering Continued Callister Slide48:  Austempering Bainite Short needles of Fe3C embedded in plates of ferrite Slide49:  Problems in Quenching Quench Cracks High rate of cooling: surface cooler than interior Surface forms martensite before the interior Austenite martensite Volume expansion When interior transforms, the hard outer martensitic shell constrains this expansion leading to residual stresses Slide50:  But how to shift the C-curve to higher times? Solution to Quench cracks Shift the C-curve to the right (higher times) More time at the nose Slower quenching (oil quench) can give martensite Slide51:  By alloying All alloying elements in steel (Cr, Mn, Mo, Ni, Ti, W, V) etc shift the C-curves to the right. Exception: Co Substitutional diffusion of alloying elements is slower than the interstitial diffusion of C Slide52:  Plain C steel Alloy steel Alloying shifts the C-curves to the right. Separate C-curves for pearlite and bainite Fig. 9.10 Slide53:  Hardenability Ability or ease of hardening a steel by formation of martensite using as slow quenching as possible Alloying elements in steels shift the C-curve to the right Alloy steels have higher hardenability than plain C steels. Slide54:  Hardnenability Hardness Ability or ease of hardening a steel Resistance to plastic deformation as measured by indentation Only applicable to steels Applicable to all materials Alloying additions increase the hardenability of steels but not the hardness. C increases both hardenability and hardness of steels. Slide55:  High Speed steel Alloy steels used for cutting tools operated at high speeds Cutting at high speeds lead to excessive heating of cutting tools This is equivalent to unintended tempering of the tools leading to loss of hardness and cutting edge Alloying by W gives fine distribution of hard WC particles which counters this reduction in hardness: such steels are known as high speed steels. Slide56:  Airbus A380 to be launched on October 2007 Slide57:  A shop inside Airbus A380 Slide58:  Alfred Wilm’s Laboratory 1906-1909 Steels harden by quenching Why not harden Al alloys also by quenching? Slide59:  time Wilm’s Plan for hardening Al-4%Cu alloy Sorry! No increase in hardness. 550ºC T Heat Quench Hold Check hardness Eureka ! Hardness has Increased !! One of the greatest technological achievements of 20th century Slide60:  Hardness increases as a function of time: AGE HARDENING Property = f (microstructure) Wilm checked the microstructure of his age-hardened alloys. Result: NO CHANGE in the microstructure !! Slide61:  As- quenched hardness Hardness time Peak hardness Overaging Hardness initially increases: age hardening Attains a peak value Decreases subsequently: Overaging Slide62:   + : solid solution of Cu in FCC Al : intermetallic compound CuAl2 4 Tsolvus supersaturated saturated +  FCC FCC Tetragonal 4 wt%Cu 0.5 wt%Cu 54 wt%Cu Precipitation of  in  Slide63:  Stable  unstable  Tsolvus As-quenched   start  finsh + Aging TTT diagram of precipitation of  in  A fine distribution of  precipitates in  matrix causes hardening Completion of precipitation corresponds to peak hardness Slide64:  Driving force for coarsening / interfacial energy Slide65:  0.1 1 10 100 hardness Aging time (days) 180ºC 100ºC 20ºC Aging temperature Peak hardness is less at higher aging temperature Peak hardness is obtained in shorter time at higher aging temperature Fig. 9.15 Slide66:  U I T Stable  unstable  As-quenched   start  finsh + Aging Tsolvus 100 ºC 180 ºC Slide67:  Recovery, Recrystallization and grain growth Following slides are courtsey Prof. S.K Gupta (SKG) Or Prof. Anandh Subramaniam (AS) Slide68:  Cold work ↑ dislocation density ↑ point defect density Plastic deformation in the temperature range above(0.3 – 0.5) Tm → COLD WORK Point defects and dislocations have strain energy associated with them (1 -10) % of the energy expended in plastic deformation is stored in the form of strain energy AS Slide69:  Cold work ↑ Hardness ↑ Strength ↑ Electrical resistance ↓ Ductility AS Slide70:  Cold work Anneal Recrystallization Recovery Grain growth AS Recovery, Recrystallization and Grain Growth:  Recovery, Recrystallization and Grain Growth During recovery 1. Point Defects come to Equilibrium 2. Dislocations of opposite sign lying on a slip plane annihilate each other (This does not lead to substantial decrease in the dislocation density) SKG Slide72:  POLYGONIZATION Bent crystal Low angle grain boundaries Polygonization AS Recrystallization:  Recrystallization Strained grains Strain-free grains Driving force for the Process = Stored strain energy of dislocations SKG Slide74:  Recrystallization Temperature: Temperature at which the 50% of the cold-worked material recrystallizes in one hour Usually around 0.4 Tm (m.p in K) SKG Slide75:  Factors that affect the recrystallization temperature: 1. Degree of cold work 2. Initial Grain Size 3. Temperature of cold working 4. Purity or composition of metal Solute Drag Effect Pinning Action of Second Phase Particle SKG Solute Drag Effect:  Solute Drag Effect SKG Grain Boundary Pinning:  Grain Boundary Pinning SKG Grain Growth:  Grain Growth Increase in average grain size following recrystallization Driving Force reduction in grain boundary energy Impurities retard the process SKG Slide79:  Grain growth Globally ► Driven by reduction in grain boundary energy Locally ► Driven by bond maximization (coordination number maximization) AS Slide80:  Direction of grain boundary migration Boundary moves towards its centre of curvature JUMP AS Slide81:  Hot Work and Cold Work Hot Work  Plastic deformation above TRecrystallization Cold Work  Plastic deformation below TRecrystallization Cold Work Hot Work Recrystallization temperature (~ 0.4 Tm) AS Slide82:  Cold work Recovery Recrystallization Grain growth Tensile strength Ductility Electical conductivity Internal stress Fig. 9.19 %CW Annealing Temperature AS

Related presentations


Other presentations created by Raffaele

Biomes freshwater
08. 01. 2008
0 views

Biomes freshwater

SummerSafety
10. 01. 2008
0 views

SummerSafety

matt nauth
10. 01. 2008
0 views

matt nauth

PhotoReactionIronOxa late
11. 01. 2008
0 views

PhotoReactionIronOxa late

APA 2004
13. 01. 2008
0 views

APA 2004

guineapigs
13. 01. 2008
0 views

guineapigs

Lecture8 HyperTexture
14. 01. 2008
0 views

Lecture8 HyperTexture

Heuristicsstudent
15. 01. 2008
0 views

Heuristicsstudent

Laughing Matter1
17. 01. 2008
0 views

Laughing Matter1

pictorial dictionary
17. 01. 2008
0 views

pictorial dictionary

CS20L Lecture Set 14 Hashing
17. 01. 2008
0 views

CS20L Lecture Set 14 Hashing

ETM Solar
21. 01. 2008
0 views

ETM Solar

51english
22. 01. 2008
0 views

51english

Lambda RED
22. 01. 2008
0 views

Lambda RED

NeillReid012005
25. 01. 2008
0 views

NeillReid012005

Rhyne
30. 01. 2008
0 views

Rhyne

stmgtsupv
07. 02. 2008
0 views

stmgtsupv

reel theory
12. 02. 2008
0 views

reel theory

urbinodek2
25. 02. 2008
0 views

urbinodek2

um rule transitional services
03. 03. 2008
0 views

um rule transitional services

Educ in SA PPt
11. 01. 2008
0 views

Educ in SA PPt

Melnik ASSE 2005 Powerpoint
07. 03. 2008
0 views

Melnik ASSE 2005 Powerpoint

Multi Site Presentation
10. 03. 2008
0 views

Multi Site Presentation

wk11 Antennas
24. 03. 2008
0 views

wk11 Antennas

fifty
28. 01. 2008
0 views

fifty

AGellmann BOPL 060704
08. 04. 2008
0 views

AGellmann BOPL 060704

EURPRE FROMTHEPOUNDTOTHEEURO
15. 04. 2008
0 views

EURPRE FROMTHEPOUNDTOTHEEURO

TomSchaller
09. 01. 2008
0 views

TomSchaller

WholeBodyVibration2
17. 04. 2008
0 views

WholeBodyVibration2

History of Swimming
23. 04. 2008
0 views

History of Swimming

Dr Kathie Cooper
24. 04. 2008
0 views

Dr Kathie Cooper

Dirk
07. 05. 2008
0 views

Dirk

Ch 03
02. 05. 2008
0 views

Ch 03

fourthgrade
22. 01. 2008
0 views

fourthgrade

SWP02
19. 01. 2008
0 views

SWP02

NextGenVisAids
04. 02. 2008
0 views

NextGenVisAids

Emma Bartle
11. 02. 2008
0 views

Emma Bartle

Eurodad INFID presentation 2005
14. 01. 2008
0 views

Eurodad INFID presentation 2005